Есть радиосистема Line6 Relay G50.
Энное время всё было прекрасно, затем в один прекрасный концерт она начала безобразничать -- стал пропадать сигнал. Выражается будто бы между передатчиком и гитарой поставили жёсткий гейт -- четверть или половина ноты попросту "пропадает", причём теряется походу на уровне именно передатчика (о чём "говорит" гаснущая лампочка сигнала на передатчике). Происходит на любом канале.
Беглый гугл выдал слово "dropouts" и пару тем, намекающих на то, что проблема известная. Я так понял, что решение -- это замена девайса у самих Line6. Однако понятное дело -- для нас такой способ геморный в силу различных обстоятельств. Плюс не уверен, что для моей больше_чем_5-летней системы такой сценарий прокатит (хотя я буду писать в Line6).
Возникла мысль -- попробовать обновить прошивку. Судя по мануалам -- нужно иметь в наличии приёмник XD-V75:
Собственно вопросы таковы:How to determine the currently installed firmware version:
Relay G30 Bodypack
-- Slide the Channel Switch to channel 1, then turn on the Relay G30 Bodypack.
-- Wait for the LEDs to settle, then immediately switch the Channel Switch from 1 to 6, then back to 1 three times (1->6->1->6->1->6->1).
-- The AUDIO LED will blink the version number - Green for the major number, and Red for the minor number, i.e. 1 green blink, 2 red blinks indicate v1.02).
Instructions for updating the Relay G30/G50/G90 Receivers:
-- Obtain an XD-V75 Receiver
-- Connect the XD-V75 Receiver to your PC or Mac using a USB cable
-- Disconnect, then reconnect the DC power plug for the XD-V75. "Loader Enabled" should be displayed.
-- Connect the XD-V75 Receiver to the G30/G50/G90 Receiver by using a cable with TRS to TRS (stereo) 1/4 inch phone plugs on either end. The cable should plug into the 1/4 inch audio output of both the XD-V75 and the G30/G50/G90 Receivers
-- Launch Line 6 Monkey, then Log In, then select "Relay G30/G50/G90 Receiver" as your device and follow the on screen instructions
Instructions for updating the Relay G30/G50/G90 Transmitters:
-- Obtain an XD-V75 Receiver
-- Connect the XD-V75 Receiver to your PC or Mac using a USB cable
-- Disconnect, then reconnect the DC power plug for the XD-V75. "Loader Enabled" should be displayed.
-- Launch Line 6 Monkey, then Log In, then select "Relay G30 Transmitter (1.0)" as your device and follow the on screen instructions.
-- If Line 6 Monkey is not able to connect to the Transmitter, select "Relay G30 (or G50/G90 depending on your system) Transmitter" as your device and follow the on screen instructions.
NOTE: G30 Transmitter owners with firmware version 1.0 should select "Relay G30 Transmitter (1.0)" in Line 6 Monkey in order to connect to the transmitter. G30 Transmitters with firmware 1.01 or later should select "Relay G30 Transmitter" in Line 6 Monkey.
1. Сталкивался ли кто с подобной ерундой? Если да -- лечили ли каким-то образом? Успешно?
2. Может быть у кого-то в наличии есть приёмник XD-V75? Попробую перепрошить, мало ли...